A: THP-10 Brush tableting machine installation and commissioning of one, the whole installation: the whole string into the top of the lifting rope can also be used a forklift to move the machine in place before the whole school level. 2, the power cord Mounting: Cable Specifications and motor power, voltage and current to adapt. Cable through the conduit through the master switch or outlet plug with a soft cable; cable through the stand after the coil into the electrical box. The steering motor should be consistent with the direction signs (that is, from the outer end of the pulley on the motor rotates counterclockwise as viewed), proofreading steering V-belt should be removed before, proof fitted with triangular belt, and then transported through the cis-button to confirm turning points correctness. 3, first cut off the power on the machine, remove the hopper 44, the feeder 57 and the mold platen 19 will be in the mold platen die hole, hole punch and die down wipe clean, then follow the steps below. ⑴ first nail insertion will undershoot the lower punch 21 holes, participate to the roots, and then align the notch body tighten the screws 59; ⑵ will be on the red nail into the upper punch 16 holes, participate to the roots, tighten ⑶ the middle mold clamping screws into the hole in the mold platen 19, attention must be below the end surface of the mold platen plane 0 ~ 0.05mm, tighten the set screws on both sides of 42. ⑷ will be installed in the fuselage mold platen, set into the lower punch, turn the large pulley 32, the upper punch into the die hole, the gap should be uniform, the upper and lower flexible, non-interference and hard friction phenomena, and then tighten the die table plate and bolt body fitted feeder etc. ⑸ detached parts. 4, filling depth adjustment loosen the adjusting nut filling both sides of the set screws, nuts can be put down to increase filling depth adjustment must tighten the screw, note the depth of filling shall not exceed 45mm. 5, tablet thickness adjustment and connected to the upper punch eccentric housing 05 on the eccentric sleeve 35, with the ruler, the numerical representation on the red into the mold depth. Adjust the eccentric first loosen the bolts fastening the housing 05 above, through the bevel gear driven eccentric sleeve 35 to adjust the film thickness, after adjustment is required to tighten the bolts and nuts to prevent loosening. 6, the film adjusting pulley rotation (clockwise) so that the next punch to its highest position, loosen the screws on both sides of the sheet adjustment nut, rotate the piece adjusting nut onto the end face of the lower end flush with the mold, adjusting After fastening screws on both sides. 7, adjust the feeder onto the lower end face of the pulley rotation rose to the highest (and the mold is flat), adjust the active joints (tone preceded pine nuts), so that near the lower end surface feeder outer edge of the rugged nut punch , and then turn the pulley (must be clockwise) the feeder moves back and forth a few times you can still meet the requirements. 8, the punch position adjusting lever directly affects the stability of the filled amount. Turn the pulley so that the next punch down the lowest position, that is filled with adjusting nut tight against the body, regulating nut up and down so that the next half-round head punch lever adjusting nut filling snapping upper end and tighten down nut. THP-10 Brush tableting machine use and operation 1, the machine should be checked before use if there is lack of edge die, cracks, deformation and other quality problems, check the machine each device is intact. 2, check whether the requirements of the original grain particles, the particles of the fines content of not more than 10%, so as not to affect the performance and life of the machine. 3, before the application of hand rotation drive pulley or jog buttons along the pressure test to determine the tablet to meet the requirements, the machine in normal operation only after the turn into production. 4, the machine has a reverse jog buttons, tableting produce glued laminated or on the red punch stuffy car and checking on the situation stormed into the mold can be used, when using only allows instantaneous trace reverse jog the machine, otherwise it will damage to the parts. 5, use should pay attention to the operation of the machine and, if abnormal noise, which should stop inspection, troubleshooting before use. THP-10 Brush tableting machine maintenance and protection of one, is equipped with a mechanical oil cup, according to the type of oil cups were injection to oil or grease. All power before refueling time, the production of visual functioning bearing temperature rise and add. 2, periodically check whether the operating flexibility and mechanical wear, find defects, should be promptly repaired. 3, once used up or shut down, the various parts of the machine should be brushed clean residual powder child; such as disabling a longer time, he shall die remove and wipe clean all machinery, mechanical glossy coated anti-rust oil. 4, die maintenance: scrub clean, dry coated antirust oil, place in a suitable container, kept clean to prevent the bump damage. THP-10 tablet press brushes note 1, then the power should pay attention to the direction of rotation of the machine, do not rewind; Taiwan Free damaged parts. 2, machine commissioning, should cut off the power, to avoid injury. 3, pour op buttons or debug observed only in relief rushed die situation on the use and can not be used to avoid damage to parts caused by accidents. 4, machine guards, security cover, etc. should be properly installed before use, can not be removed. 5, dies should be no cracks, deformation, lack of edge and other quality problems, do not use substandard goods, in order to avoid damage to the machine and affect the quality of the tablet. 6, adjusting mechanical or troubleshooting, you must shut down for, in order to avoid personal injury. 7, refueling, must not allow the oil spill to the outside, so as not to affect tablet contaminated material quality. Two: YST-60 Brush tableting machine that models the entire body using stainless steel production, applicable to suppress a variety of powder molding, the press and high precision, reliable performance, tabletting stable, high yield, enabling two-way repression. All electrical devices are used in the "PLC" programming control, all the action can be time regulation. All imported hydraulic components, the key positions are mechanical and electrical dual control, all the action can be transferred through the PLC best state, is to suppress the large product choice.